通信学报 ›› 2017, Vol. 38 ›› Issue (3): 92-100.doi: 10.11959/j.issn.1000-436x.2017063

• 学术论文 • 上一篇    下一篇

基于DG-PSP的不同符号速率PCMA信号盲分离算法

郭一鸣1,彭华1,杨勇1,魏雪娟1,王浩2   

  1. 1 解放军信息工程大学信息系统工程学院,河南 郑州 450002
    2 解放军61081部队,北京 100094
  • 修回日期:2016-12-16 出版日期:2017-03-01 发布日期:2017-04-13
  • 作者简介:郭一鸣(1990-),男,河北邢台人,解放军信息工程大学博士生,主要研究方向为通信信号处理、信号逆向分析等。|彭华(1973-),男,江西萍乡人,解放军信息工程大学教授、博士生导师,主要研究方向为软件无线电、通信信号处理等。|杨勇(1988-),男,云南大理人,解放军信息工程大学博士生,主要研究方向为盲信号处理、信道编译码技术等。|魏雪娟(1988-),女,河南兰考人,解放军信息工程大学硕士生,主要研究方向为通信信号处理等。|王浩(1987-),男,河南信阳人,解放军 61081 部队助理工程师,主要研究方向为卫星导航信号接收处理、抗干扰等。
  • 基金资助:
    国家自然科学基金资助项目(61401511)

Blind separation algorithm of PCMA signals with different symbol rates based on DG-PSP

Yi-ming GUO1,Hua PENG1,Yong YANG1,Xue-juan WEI1,Hao WANG2   

  1. 1 School of Information Systems Engineering,PLA Information Engineering University,Zhengzhou 450002,China
    2 61081 Troop of PLA,Beijing 100094,China
  • Revised:2016-12-16 Online:2017-03-01 Published:2017-04-13
  • Supported by:
    The National Natural Science Foundation of China(61401511)

摘要:

针对非合作接收不同符号速率PCMA混合信号,提出一种基于双网格逐幸存路径处理(DG-PSP,double grid per-survivor processing)的分离算法。将2路信号分量的信道状态与输入分别视为2组动态网格,通过分别迭代更新2组网格状态实现混合信号重构,进而实现PCMA信号盲分离。重点研究了联合译码的迭代分离结构,并对不同参数估计误差下算法性能做了详细分析比较。所提算法复杂度与传统PSP算法相当,同时仿真结果表明,算法性能逼近联合界,当采用迭代处理时,在误比特率10?2数量级上经过一次迭代就能获得2 dB的信噪比增益,经过2次迭代则有近3 dB的信噪比增益。

关键词: 成对载波多址, 不同符号速率, 双网格, 盲分离

Abstract:

A blind separation algorithm was proposed for PCMA signals with different symbol rates based on double grid per-survivor processing (DG-PSP).The channel states and two input signal components were treated as two dynamic grids,receiving mixed-signal reconstructed by respectively iterative updating the two groups of grid status,thus achieving blind signal separation.The joint iterative decoding separation structure was focused,and a detailed analysis and comparison under different error estimation of parameters was shown.The complexity of the algorithm is similar to the traditional PSP algorithm.Simulation results show that,a gain of about 2 dB in signal-noise ratio can be obtained after the first iteration at a bit error rate of 10?2,and a gain of nearly 3 dB in signal-noise ratio can be obtained after the second iteration.

Key words: PCMA, different symbol rates, double grid, blind separation

中图分类号: 

No Suggested Reading articles found!